Basic Info.
Product Description
1) 300K pixels digit camera
2) PIR detector
3) Video motion detection
4) IR for night use
5) Video upto QVGA(320× 240)
6) Ready time recording
7) Support upto 16GB SD card
8) Adjusted to QCIF, CIF, VGA
10) 16 zone wireless detectors
11) Alarm to 5 groups phone
12) Alarm to 1 group monitor center
13) Alarm to 1 group SMS center
14) Alarm to fix IP address
15) Alarm to 2 groups Email
16)Interval time to reporting
17) Fixed time of arm and disarm
18) Built-in four- bands GSM 9) Listen-in function
19) Built-in lithium battery
20) with one wire input alarm
How to use it:
1) Open the battery cover, put SIM cart in it, Inserts the SD card(FAT32) into the base(if you have it), put the power 5V/2A DC into the base, put down switch of the base to open power supply. The LED turns to red and last for 20, and it will start to search GSM network. After 20 seconds, the LED is flashing in orange and the alarm system begins to read the information of the SIM memory. It will enter into the status of disarm and LED is go still green. It will be turned to be green and flashing in the status of alarm when you use controller to set the base in alarm. The LED is red and flashing when the base is in alarming.
2) you can send the message to setup the base. The format: Password #operation code # content # 123456#11#1#; Set the base alarm; LED green and flashing in the base 123456#31#99998888#1#1#0#, set phone 99998888 and sent out message and picture when alarm. 123456#1#1#; Get one picture by your mobiphone if MMS setting is ok, Shus as MMS setting show in China( other country will be different): Access Point Name(APN): CMWAP; Set GPRS Access point. Username: (empty); Set MMS Uesr name. Password: (empty); Set MMS Uesr Password. Gateway IP (proxy) address(IP): 10.0.0.172; Set IP Address. Port: 9201; Set Port MMS (Relay) Server URL: HTTP: /MMS. Monternet. COM; Set MMS Homepage.
How to add more detectors? You can add new detector, such as wireless door sensors, PIR Sensors, gas and smoke detectors when you push the reset key(inside the battery cover) untill the LED change from green to red. You should trigger every detector, and the red LED will flash and shows successful. After you finish doing it, you can push the reset key again or waitting 20 seconds, it ends and automatically enter into working state. (with green LED), you can program it by 71# --86# How to cancel the lost detector? It often happens that some of coded detectors are lost. You can cancel the coded information of this detector so that it can not control your alarm system. Just reset the alarm system by keeping reset key and turn on power and then beep or LED flashes, it shows reset is successful. All registered detector have been deleted and password is123456. You can register them again with the above solution.
How to control the base with remote controllers? When you press, "alarm", the LED of the base will be turned green with flashing. It shows the base is in arming status, it will alarm and dial out when you remove the door sensor, switch PIR Sensor, go across from the front of camera and so on. The LED will turn to red with flashing when the base is alarm. When you press, "disalarm", the LED of the base will turn green and does not flash. It won't alarm and dial out. When you press "Emergency help", it will alarm and send MMS and SMS or dial out no matter it is under arming status or disarming status. The LED will be red with flashing.
Address:
Sanpinjie, 2-59, Quanzhou, Fujian, China
Business Type:
Manufacturer/Factory
Business Range:
Security & Protection
Company Introduction:
Established in 1994, Xinguang has already gained a high reputation for quality products. We insist that quality is a priority for development and good service is the key to success. With experienced workers, innovative engineers and advanced equipment, we guarantee excellence in product and quality. For more details, view our homepage and contact us.